壹、鉆孔規格:
1、鉆孔口徑應根據鉆探目的和鉆進工藝確定。采取原狀土樣的鉆孔,口徑不得小於91mm,僅需鑒別地層的鉆孔,口徑不宜小於36mm;在濕陷性黃土中,鉆孔口徑不宜小於150mm。The bore diameter shall be determined according to the drilling purpose and drilling technology. The bore hole of undisturbed soil sample shall not be less than 91mm in diameter. Only the bore hole of stratum identification shall be used, and the bore hole shall not be less than 36mm in diameter. In collapsible loess, the hole diameter should not be less than 150mm.
2、深度超過100mm的鉆孔以及有特殊要求的鉆孔包括定向鉆進、跨孔法測量波速,應測斜、防斜,保持鉆孔的垂直度或預計的傾斜度與傾斜方向。對垂直孔,每50m測量壹次垂直度,每深100m允許偏差為±2°。對斜孔,每25m測量壹次傾斜角和方位角,允許偏差應根據勘探設計要求確定。smluntan论坛3,日韩电影,情宿外欲下载及方位偏差超過規定時,應及時采取糾斜措施。
二、鉆進與護壁
1、鉆進方法應符合下列要求:
壹 對要求鑒別地層和取樣的鉆孔,均應用回轉方式鉆進,取得巖土樣品。遇到卵石、漂石、碎石、塊石等類地層不適用於回轉鉆進時,可改用振動回轉方式鉆進。
二 在地下水位以上的土層中應進行幹鉆,不得使用沖洗液,不得向孔內註水,但可采用能隔離沖洗液的二重或三重管鉆進取樣。
三、采取鑒別土樣及巖芯
1、在土層中采用螺旋鉆頭進時,應分回次提取擾動土樣。回次進尺不宜超過1.0m,smluntan论坛3,日韩电影,情宿外欲下载或重點研究部位,回次進尺不宜超過0.5m,並應滿足鑒別厚度小至20cm的薄層的要求。
2、在水下粉土、砂土層中鉆進,當土樣不易帶上地面時,可用對分式取樣或標準貫入器間斷取樣,其間距不得大於1.0m。取樣段之間則用無巖芯鉆進方式通過,亦可采用無泵反循環方式用單層巖芯管回轉鉆進並連續取芯。When drilling in the silt and sand layer under water, if the soil sample is not easy to take to the ground, the fractional sampling or the standard penetrator can be used for intermittent sampling, and the spacing shall not be more than 1.0m. Between sampling sections, coreless drilling is adopted, or single core pipe rotary drilling and continuous coring can be adopted without pump reverse circulation.
四、地下水觀測
1、鉆進中遇到地下水時,應停鉆量測初見水位。為測得單個含水層的靜止水位,對砂類土停鉆時間不少於30min;對粉土不少於1h;對粘性土層不少於24h。並應在全部鉆孔結束後,同壹天內量測各孔的靜止水位。水位量測可使用測水鐘或電測水位計。水位允許誤差為±1.0cm。
2、鉆孔深度範圍內有兩個以上含水量,且smluntan论坛3,日韩电影,情宿外欲下载要求分層量測水位時,在鉆穿第壹含水層並進行靜止水位觀測之後,應采用套管隔水,抽幹孔內存水,變徑鉆進,再對下壹含水層進行水位觀測。
四川瑞特消防科技有限公司 地址:成都市金牛區高科技產業園興盛西路2號 網站地圖|網站首頁
蜀ICP備08111268號 Copyright © 2008-2009 All Rights
Reserved. 技術支持:三以網絡